OSMO Wood Coat : Construction method
For new wood
To remove everything dust from surface. Such as oil. Tar, molt, dust etc…Dry thoroughly less 18% water content.
Polished up before work with several sand paper of #120-150 or #180-240.
Wood powder blow off by brush or air blow to clean up for the surface.
Remaining about seeping stain it should be removed with a scraper or cutter knife.
Sticky tar will wipe off with lacquer thinner.
Surface treatment is necessary to improve the finish nicely.
Old materials / Recoat
To remove everything dust from surface. Such as oil. Tar, molt, dust etc…Dry thoroughly less 18% water content.
Polished up before work with several sand paper of #120-150 or #180-240.
Wood powder blow off by brush or air blow to clean up for the surface.
Remaining about seeping stain it should be removed with a scraper or cutter knife.
Sticky tar will wipe off with lacquer thinner.
Surface treatment is necessary to improve the finish nicely.
Osmo Wood Coat Paint Dilution ratio / The Main : Cure =10 : 1
The main and the curing agent are uniformly stirred beforehand. Subdivide the base and curing agent both to apply coating area accurately measurement. The main : Cure agent 10:1 and mix them up uniformly.
No dilution any requires because the paint is adjusted to the coating viscosity.
Select the coating method ( Brush, Roller, Spray ) according to the coating environment. Use brush or roller according to the smoothness of the wood surface.
Do not paint a large area at once, apply evenly while penetrating the wood little by little.
Depending on the degree of absorption the wood with a low suction can be infiltrated repeatedly by the wet-on wet method.
Wood with low suction is penetrated while adjusting the application amount according to the degree. Optimal paint is slightly raised on the wood surface.
Be careful not to apply a thick coat so as not to form a paint film like varnish on the wood surface. Coating may be peeled off or cracked due to the expansion.
To dry completely 1-2hours in summer, 5-6 hours in winter.
Leave the material 7days to dry to the strength of the wood.
It cures and dries about 2-3 days and is treated water repellency and antifouling performance appeare..
It takes 7 days to hardness is improved and the wood is completely dried. Please consider the drying time and curing period
OSMO is suitable for natural solid wood, it is a paint penetrates deep into the wood and exerts effect, Varnished wood does not have a sufficient effect.
The finish varies depending on the type of xylem, so make a trial coating with the same material in advance and check the finish.
Avoid painting if the temperature is below 5C or the humidity is above 80% or if the evocation is not enough and dew condensation is considered.
Avoid painting when there is a risk of rain, snowfall, or strong wind in outdoor painting.
Please use the paint after sufficiently stirring make the contents even
Use water or hot water to clean equipment Wash paint with hot water until it dries, then wipe off paint with lacquer thinner after drying.
Seal the remaining paint and store in a cool, dark place.
Please refer to the safety data sheet SSD for details on product safety.
Film performance
Alkali resistance test: Spot test, dipped in 5% sulfuric acid aqueous solution for 24 hours(20C) : No abnormality.
Acid resistance test: Spot test, immersed in 5% NaOH aqueous solution for 24 hours (20C) : No abnormality.
Water resistance: tap water, immersed for 10 days (40C) No abnormality.
Accelerated weather resistance; Discoloration visually confirmed after irradiation for 2500 hours with a xenonweatherometer : No abnormality.
Heat cycle: 60Cx3hours, -20Cx3hours (10cycle) : No abnormality.
BL HY-COATER
PRESENCE Co., Ltd. / BADLAND
4-18-1 Minamikase Saiwaiku Kawasaki Kanagawa JAPAN
ZIP CODE : 212-0055
TEL +81-44-587-3139 / FAX +81-44-580-3431 / e-mail : info@badland.net
Comment On Facebook