OSMO Wood Coat
OSMO Wood Coat is excellent product which is reduced in discoloration by ultraviolet degradation and resistant for long term period.
2 pot type aqueous Polysiloxane System inorganic hybrid coat. To provide high level resistant for all wood materials which is reduced discoloration and degradation environmentally friendly. As you can see the high permeability effect. Do forming a coating film have an excellent weather resistance and antifouling properties even at room temperature.
Characteristic of OSMO Wood Coat
As a feature about Weather resistance / Contamination resistance / Chemical resistance.
Aqueous polysiloxane System inorganic hybrid paint with High weather resistance for all wood materials.
To suppress deterioration / Discoloring damage
Excellent protection ability against long-term deterioration and discoloring damage despite being a transparent coating on wood.
Can be painted with one process
Without any primer. Can be painted directly to the wood materials.
The compared bothe of them after constructed 6months / Shooting date : Dec 15 ,2019.
2019.6.13 Setted up facing south.
Ceder wood.
Dilution ratio : Main / Cure agent= 10 : 1
Finger to touch dry : Room temperature (20c) x 30-60min
Hrdened dry : Room temperature (20C) x 24hours
Coating amount : 200-300g/m2
Construction method
For new wood
To remove everything dust from surface. Such as oil. Tar, molt, dust etc…Dry thoroughly less 18% water content.
Polished up before work with several sand paper of #120-150 or #180-240.
Wood powder blow off by brush or air blow to clean up for the surface.
Remaining about seeping stain it should be removed with a scraper or cutter knife.
Sticky tar will wipe off with lacquer thinner.
Surface treatment is necessary to improve the finish nicely.
Old materials / Recoat
To remove everything dust from surface. Such as oil. Tar, molt, dust etc…Dry thoroughly less 18% water content.
Polished up before work with several sand paper of #120-150 or #180-240.
Wood powder blow off by brush or air blow to clean up for the surface.
Remaining about seeping stain it should be removed with a scraper or cutter knife.
Sticky tar will wipe off with lacquer thinner.
Surface treatment is necessary to improve the finish nicely.
Osmo Wood Coat Paint Dilution ratio / The Main : Cure =10 : 1
The main and the curing agent are uniformly stirred beforehand. Subdivide the base and curing agent both to apply coating area accurately measurement. The main : Cure agent 10:1 and mix them up uniformly.
No dilution any requires because the paint is adjusted to the coating viscosity.
Select the coating method ( Brush, Roller, Spray ) according to the coating environment. Use brush or roller according to the smoothness of the wood surface.
Do not paint a large area at once, apply evenly while penetrating the wood little by little.
Depending on the degree of absorption the wood with a low suction can be infiltrated repeatedly by the wet-on wet method.
Wood with low suction is penetrated while adjusting the application amount according to the degree. Optimal paint is slightly raised on the wood surface.
Be careful not to apply a thick coat so as not to form a paint film like varnish on the wood surface. Coating may be peeled off or cracked due to the expansion.
To dry completely 1-2hours in summer, 5-6 hours in winter.
Leave the material 7days to dry to the strength of the wood.
It cures and dries about 2-3 days and is treated water repellency and antifouling performance appeare..
It takes 7 days to hardness is improved and the wood is completely dried. Please consider the drying time and curing period
OSMO is suitable for natural solid wood, it is a paint penetrates deep into the wood and exerts effect, Varnished wood does not have a sufficient effect.
The finish varies depending on the type of xylem, so make a trial coating with the same material in advance and check the finish.
Avoid painting if the temperature is below 5C or the humidity is above 80% or if the evocation is not enough and dew condensation is considered.
Avoid painting when there is a risk of rain, snowfall, or strong wind in outdoor painting.
Please use the paint after sufficiently stirring make the contents even
Use water or hot water to clean equipment Wash paint with hot water until it dries, then wipe off paint with lacquer thinner after drying.
Seal the remaining paint and store in a cool, dark place.
Please refer to the safety data sheet SSD for details on product safety.
Film performance
Alkali resistance test: Spot test, dipped in 5% sulfuric acid aqueous solution for 24 hours(20C) : No abnormality.
Acid resistance test: Spot test, immersed in 5% NaOH aqueous solution for 24 hours (20C) : No abnormality.
Water resistance: tap water, immersed for 10 days (40C) No abnormality.
Accelerated weather resistance; Discoloration visually confirmed after irradiation for 2500 hours with a xenonweatherometer : No abnormality.
Heat cycle: 60Cx3hours, -20Cx3hours (10cycle) : No abnormality.
The price
Main : 1kg
Cure agent : 100g
OSMO Wood Coat 4kg Kit : 108,300JPY
Main : 4kg
Cure agent : 400g
OSMO Wood Coat 15kg Kit : 382,500JPY
Main : 15kg
Cure agent : 1.5kg
Shipping charge / as hazardous goods
How to Order
Paint in general is treated as hazardous goods, so for shipping charges, we must make individual estimates by airline according to country and region.
We will then send you a bill including those shipping charges via paypal. After checking that amount, please decide whether or not to purchase our products.
paypal is our only payment method. You can cancel the order at any time.
Furthermore, please note that it will be about 10~14 days before items are shipped.
Estimated shipping charges
Forwarder & Transportation : ANA cargo or K-Line Logistics
The minimum fee is set for international transportation of dangerous goods.
The following is the minimum fee in each region.
Central America : 55,000〜65,000JPY
South America : 75,000〜85,000JPY
Europe / Russia : 60,000〜75,000JPY
India / Middle east : 75,000〜85,000JPY
Africa : 65,000〜85,000JPY
Recruiting Distributors & Dealers
Contact : Recruiting Distributors & Dealers
BL HY-COATER
PRESENCE Co., Ltd. / BADLAND
2-39-45 Shishigaya Tsurumiku Yokohama Kanagawa Japan
ZIP CODE : 230-0073
TEL +81-45-717-7026 / FAX +81-45-717-7027 / e-mail : info@badland.net
Comment On Facebook